Rear corner doors
On the curved aluminium, is it possible to curve it or are they special pieces?
I don't really want to put old doors on they are all pitted
Mason
Announcement Block
As of 12/1/2021, a major update of the forum software was accomplished
Update: 3/7/2024: The Eagles email account at GoDaddy no longer works. I have set up a gmail account as a workaround: eaglesinternational.email at gmail.com
Registration is open to the public (*) and free from any cost or obligation. Please allow up to 36 hours for your application to be processed. If you have problems registering, please email me at: eaglesinternational.email at gmail.com
(*) spambots will be deleted -- only legitimate public applications will be processed.
Reminder: the "quick links" menu offers you the best navigation of this forum -- you need to be registered and logged in to see that menu.
As of 12/1/2021, a major update of the forum software was accomplished
Update: 3/7/2024: The Eagles email account at GoDaddy no longer works. I have set up a gmail account as a workaround: eaglesinternational.email at gmail.com
Registration is open to the public (*) and free from any cost or obligation. Please allow up to 36 hours for your application to be processed. If you have problems registering, please email me at: eaglesinternational.email at gmail.com
(*) spambots will be deleted -- only legitimate public applications will be processed.
Reminder: the "quick links" menu offers you the best navigation of this forum -- you need to be registered and logged in to see that menu.
Rear corner doors
-
- Posts: 322
- Joined: Thu Jun 14, 2018 11:37 am
- Bus Model: 1968 model 05 Eagle series 60 and B500
- Location: McCook NE
Rear corner doors
1968 05 Series 60/B500 swap 2019-2021
1971 05 8v71 Spicer 4 speed parts bus
1971 05 8v71 Spicer 4 speed parts bus
- beltguy
- Site Admin
- Posts: 2667
- Joined: Wed Oct 08, 2008 4:39 am
- FMCA #: F246286
- Bus Model: 1985 Eagle 10 with Series 60 and Eaton AutoShift 10 speed transmission (SOLD)
- Location: Evergreen, CO
- Contact:
Re: Rear corner doors
Mason, I don't have direct experience on this, but I think you can form to aluminum. Wayne has direct experience and I hope he jumps in here.
I would try a scrap piece. I would make a buck or use a big log to control the radius.
Jim
I would try a scrap piece. I would make a buck or use a big log to control the radius.
Jim
Jim Shepherd
Evergreen, CO
'85 Eagle 10 with Series 60 & Eaton AutoShift 10 speed transmission SOLD
2005 Dodge 2500 with 5.9 Cummins and 6 speed manual 2022 Sunset 28 foot trailer
Bus Project pages: http://beltguy.com/Bus_Project/busproject.htm
Blog: https://beltguy.com/Travelogue/
Email: eaglesinternational.email at gmail.com NOTE this email box is only for general correspondence related to the forum and not technical advice. Technical questions will not receive a response.
Evergreen, CO
'85 Eagle 10 with Series 60 & Eaton AutoShift 10 speed transmission SOLD
2005 Dodge 2500 with 5.9 Cummins and 6 speed manual 2022 Sunset 28 foot trailer
Bus Project pages: http://beltguy.com/Bus_Project/busproject.htm
Blog: https://beltguy.com/Travelogue/
Email: eaglesinternational.email at gmail.com NOTE this email box is only for general correspondence related to the forum and not technical advice. Technical questions will not receive a response.
- rusty
- Moderator
- Posts: 1547
- Joined: Thu Oct 09, 2008 3:22 pm
- FMCA #: F341087
- Bus Model: 1972 05 completed 2003
1994 15/45 in progress - Location: Johnstown Co.
Re: Rear corner doors
Mason sorry for the late reply something was wrong and I couldn't reply. Anyway the way I did it was make a good form with a slightly smaller radius than the bus. the form should be made so you can use clamps on both sides. With a little heat and a lot of muscle you can form the aluminum. It will spring back a little.The piece should be a little longer than you need so you can trim it. Then with the use of clecos ( sp ) drill and fit the piece to the bus before you rivet. If you need some clecos for the price of shipping both ways I will send you some. That method works for sheet goods. Don't use heat on the fluted stuff it will mess with the anodizing. With a solid form you can bend it by hand.
-
- Posts: 322
- Joined: Thu Jun 14, 2018 11:37 am
- Bus Model: 1968 model 05 Eagle series 60 and B500
- Location: McCook NE
Re: Rear corner doors
Ok thanks Wayne.
Good to know about the anodizing.
Might have to take up your offer on the clecos. I will let you know.
Mason
Good to know about the anodizing.
Might have to take up your offer on the clecos. I will let you know.
Mason
1968 05 Series 60/B500 swap 2019-2021
1971 05 8v71 Spicer 4 speed parts bus
1971 05 8v71 Spicer 4 speed parts bus